Omega screw lookup
Type a screw number, a calibre, or the job the screw does (click, dial, pallet cock). You get the Omega screw number, what it holds, and every calibre it fits, straight from Omega's own spare-parts catalogues. Below the lookup is how to identify vintage Omega screws and the traps that catch people out.
Screw numbers are four digits, mostly 2000 to 3999, sometimes with a suffix (2033 P) or a calibre prefix (1140.2310). Calibres are the movement number: 565, 1012, 30 T2, 27 CHRO C12. Lost the screw and only know the part it held? Type the calibre and the part number, for example .
Data: Watch Breaker database snapshot.
Was someone in here before you?
Don't trust where a screw came out. A previous repair may have put the wrong one in. Check every screw as it comes out, before it goes in the tray.
- Count them. Compare what you took out with the list for your calibre above. One extra or one missing means someone has been in.
- Match the twins. Screws that hold the same part should look the same. The one with a different head, colour or length is the stranger.
- Look at the height. A seated head sits level with its neighbours. Standing proud or sunk low means the wrong length.
- Feel it. It should turn freely until the head seats. If it gets tight early, stop: wrong thread or wrong length.
- Check the slot. A chewed slot or a fresh bright scratch means it was forced last time.
Never force a screw. Found a stranger? Type your calibre into the lookup to see which numbers belong.
How Omega numbers its screws
On vintage Omega movements a bare four-digit number tells you what kind of part it is before you know anything else. The catalogues use blocks:
- 2000–3999: screws. Every screw in the movement and the case fastenings.
- 4000–4999: jewels.
- 5xxx: screw tubes (for example 5169, the tube for the pallet-cock screw on the 690).
- 6xxx: bushings. 7xxx: mounted assemblies. 9xxx: electronic parts.
The catch: Omega's 1962 crown numbers run from 1307 to 4509, right across the screw and jewel blocks. Crown 2311 and screw 2311 are different objects. Always say screw 2311, never just "Omega 2311".
Eight things that trip people up
1. One screw number often fills many holes
Screw 2460 on the calibre 980 holds five different springs and clamps. Screw 2257 holds the barrel bridge (twice), the train wheel bridge and the balance cock on a 455. Screw 2008 holds both the barrel bridge and the train wheel bridge on a 162. A bag of "assorted screws" from one movement is usually two or three numbers, not twenty, so count quantities, not varieties.
2. The same job can carry two numbers in one family
The three-screw oscillating-weight segment takes screw 2143 on the 332 but 2144 on the 351. The catalogue text is word for word the same. Match screws by calibre, never by the description alone.
3. The same number can do a different job in another section
In the 245, screw 2102 fixes the enlargement ring. In the 455, 2102 is the crown-wheel-core screw, a job the 245 gives to 2301. A bare screw number copied from one calibre's page doesn't prove it fits another. Look it up by calibre.
4. Prefixed numbers aren't interchangeable across families
Some catalogue sections carry a calibre prefix. The setting-lever screw is 23.4.3143 on one family and 30.3143 on another. The trailing number says what the part is, not what it fits. Keep the prefix.
5. Balance screws come in weights
The 330 family lists three balance screws: 2915 plain, 2927 light and 2926 heavy. The 470–520 group uses 2965 plain, 2966 heavy and 2967 light. Print errorThe calibre 510 page prints 2966 and 2967 with the weights the other way round. Check the weight before you poise a 510 balance with them.
In mid-1959 Omega started moving to the screwless balance, beginning with the calibre 482. Later movements have no balance screws at all.
6. Casing-clamp screws changed thread mid-production
Omega increased the casing-clamp screw thread from 0.70 mm to 0.80 mm, replacing screw 2281 with 2297 and 2719 with 2722. The changeover movement number is different for each calibre family, so a clamp screw can help bracket a movement's age within its own family. On the 540, Omega's notice says the clamp screws actually used carry 3400; the 3210 printed in the parts list was never used in production.
7. Case screws aren't movement screws
On the 160 series, 2708 is the dog-screw that holds the movement in the case. 2711 fixes the casing ring to the case. They look alike and do different jobs; don't swap one for the other.
8. Suffixes matter
Every screw in the calibre 863 guide carries a P suffix: 2033 P, 2224 P, 2237 P and so on. The 861 uses the same base numbers without the P. They are different parts. Don't drop the suffix.
Colour and printing conflicts
Don't identify an Omega screw by colour alone. Screw 2989 on the calibre 1110 is printed black in one Omega catalogue and blue in an Omega maintenance guide from a few months later. And the calibre 1000 page lists two different numbers (2332 and 2631) for the rotor-axle screw. Where Omega's own print disagrees, this lookup flags it.
The most widely shared Omega screws
These numbers fit the most calibres in the database. Tap one to see every calibre it fits.
| Screw | Job | Calibres |
|---|
Questions
Are Omega screws interchangeable between calibres?
An identical Omega part number means the same part, whichever calibre it's listed under. Look up the number, not the description. Two screws described the same way in different calibres can carry different numbers, and those aren't interchangeable.
Which Omega screw fits the most calibres?
Screw 2154, the hairspring-stud screw, is listed for 56 calibres, from the 240 series through the 30 mm, 550–565 and 750 families. Screw 2138, which holds the bearing for the ratchet-wheel driving gear on automatics, is close behind at 54.
My number shows up as a crown or a jewel somewhere else. Which is it?
Possibly both. Omega's crown numbers (1307 to 4509) overlap the screw block (2000 to 3999) and the jewel block (4000 to 4999). Check the category before you buy.
My screw or calibre isn't listed.
The database is built page by page from Omega's catalogues and is still growing. Email id@watchbreaker.com with the number or calibre and it will be checked against the books.
Where does the data come from?
Omega's printed GF 620 spare-parts catalogues, Omega technical guides and Omega service bulletins. Each result lists its sources. Watch Breaker copies the part numbers and fitments as facts and doesn't reproduce catalogue pages.
Watch Breaker is an independent identification service and is not affiliated with, endorsed by or connected to Omega SA or the Swatch Group. Omega is a trademark of Omega SA. Part numbers are quoted for identification and are copied by hand from Omega's catalogues, so check every number against your part before you buy. Terms.